Engineering Geology

Engineering Geology

The Study of Cementation Level Effect on the Strength Characteristics and Shear Wave Velocity of Coarse-Grained Alluvium in Eastern Areas of Tehran, Iran

Authors
Maziar Hosseini
Majid Taromi
Mehdi Soltani Negar
10.52547/jeg.14.4.581
Abstract
Introduction

Series A of coarse-grained alluvial deposits of Tehran are extended in eastern and north-eastern areas of Tehran. Analyzing and studying of these alluvial deposits from a geological point of view as well as their creation time and general characteristics such as the deposits’ mineral types, their source, and formation conditions, gives a better point of view to geotechnical engineers about exploring their characteristics as well as geotechnical aspects in underground structure design, excavations, and foundation design processes. On the other hand, in order to analyze stability, estimating the factor of safety and the seismic design of these structures, considering their location, which is in Tehran with a high seismic hazard area, the necessity of knowing the exact mechanical and dynamic properties of Tehran's alluvium is felt more than ever.

Material and methods

Due to the grain size of Tehran’s coarse-grained alluviums (series A) as well as high level of cementation of them, it is impossible (or maybe so difficult) to make undisturbed samples in order to do experiments. Such that it is excavated 23 boreholes with 30 to 140 meters depth as well as 17 test wells with 20 meters depth in an area which was extended in 10 kilometers in long which were located in Tehran’s No. 13 and No. 14 districts (as it can be seen in Figure 1). During the excavation of the entrance ramp and tunnel of eastern highway of Tehran, in-situ tests have been done in different sequences. Since it was important to investigate real behavior of these alluviums, different in-situ tests such as plate load test, in-situ shear test, pressuremeter test, and downhole test have been done as well as many laboratory and field tests. Furthermore, (1) X-Ray Diffraction (XRD) and (2) X-ray Fluorescence (XRF) as well as (3) Scanning Electron Microscopy (SEM) methods, have been used to explore the type of minerals and those used in cementation.











(ب)







Figure 1. a) Geological plan and the location of boreholes and test wells in the alignment of East Tehran Freeway

Results and discussion

Based on the results of XRD tests, it is quite clear that the largest weight percentages of tested samples are lime and silica.

Calcium and magnesium levels-as the high-power cations in flocculation process-in soil sample No. 1 (soil with high cementation level) are much more than soil sample No. 2 (soil with moderate cementation level).

This is the cause of high cementation level of soil sample No. 1 comparing with soils sample No. 2. A rapid increase in stress level can be seen in in-situ shear test results, in low shear displacements, up to reaching a maximum of τp (peak point) and afterwards reduction in shear stress with softening behavior.

Cohesion and shear strength levels also increase by increasing the depth. According to the plate load tests results, an increase in soil modules changes can be seen in different depths by depth increasing.

Large tendencies to increase in volume and dilation can be seen in under shear load cemented soils, after applying a primary compression on them. A brittle behavior with the occurrence of a certain peak can be seen in cemented samples. The significant increase in strength is directly related to the severe dilation rate, which can be seen in cemented samples results. The shear strength would be decreased, if this cement is broken during the particles’ displacements.

The results of downhole tests are shown in Figure 2. According to this figure, it has been explored that Vs,30 is about 600 m/s in moderate cemented soils while it is about 850 m/s in highly cemented soils. Because of the homogeneity and uniformity of sedimentary deposits, shear wave velocity is increasing due to the higher density of the layers and high level of cementation in both of the soil types. However, this increase is not significant at depths above 25 meters.

Conclusion

Based on the results, cementation level of the eastern coarse-grain-alluvium of Tehran is moderate to high and minerals used in cementation of this type of soil are generally carbonated and especially calcite.

Investigating the level of cementation of soil as well as the results of chemical analysis and in-situ tests, it can be found that the strength and deformation parameters of the soil are directly related to the degree of its cementation.

Based on the obtained results, the deformation modulus increases by about 25%, the cohesion by about 55% and the shear wave velocity by about 30% with increasing the degree of cementation (Table 1).

Increases of these parameters are directly related to depth. However, the cementation level does not significantly affect the internal friction angle of the soil.

Table 1. Average results of in-situ shear tests



Deformation Modulus (MPa)
Peak Friction Angle (deg.)
Cohesion

(kPa)
USCS
Depth

(m)
Sample


50-60
39
30-35
GW-GM
5
Moderately Cemented Soil

(M.C. Soil)


75-85
41
50-60
SP-SC
10


85-90
41
50-60
GW-GC
15


95-105
41
50-60
GW-GC
20


60-70
39
35-40
GW-GM
5
Highly Cemented Soil (H.C. Soil)


75-85
39
50-60
GW-GC
10


110-120
42
65-75
GW-GC
15


125-140
41
110-120
GC
20




Keywords
Tehran eastern alluviums
In-situ tests
Chemical analysis
Cementation
Shear Wave Velocity
1. Rieben E. H., "The geology of Tehran plain", American Journal of Science (1955) 617-639.## 2. Rieben E. H., "Geological observations on alluvial deposits in northern Iran", Geological Survey of Iran 9 (1966) 39. ## 3. Engalenc M., "Contribution a la Geologie Geomorphologie. Hydrogeologie, dela region de Teheran (Iran)", C.E.R.H., Montpellier, France (1968) 365. ## 4. Pedrami M., "Pasadenian Orogeny and Geology of Last 700,000 Years of Iran", Geological Survey of Iranian (1981) 273. ## 5. Abbassi M., Farbod Y., "Faulting and folding in quaternary deposits of Tehran’s piedmont (Iran)", Journal of Asian Earth Sciences, Vol. 34 (4), (2009) 522-531. ## 6. علیایی م.، یثربی س. ش.، امامی م.، "روشی برای بررسی رفتار لرزه‌ای دیواره‌های حفاظت شده گودبرداری‌های عمیق با سیستم دیوار برلنی در آبرفت درشت دانه"، مجلۀ علمی- پژوهشی مهندسی عمران مدرس، ۱۲ (۴) (۱۳۹۱) ۳۷-۴۹.## 7. طارمی م.، حسینی م.، پورهاشمی م.، صادقی م.، "مهندسی ارزش بر اساس رفتارنگاری تونل طی مرحلۀ حفاری (مطالعۀ موردی تونل حکیم)". نشریۀ زمین‌شناسی مهندسی، ۱۱ (۱) (۱۳۹۶) ۵۱-۷۲.## 8. Sharifzadeh M., Kolivand F., Ghorbani M., Yasrobi Sh., "Design of sequential excavation method for large span urban tunnels in soft ground–Niayesh tunnel", Tunnelling and Underground Space Technology, Vol. 35 (2013) 178-188. ## 9. حائری م.، یثربی س. ش.، ارومیه‌ای ع.، اصغری ا.، "تأثیر سیمانی شدن بر مقاومت برشی آبرفت‌های درشت دانه تهران"، نشریۀ علمی پژوهشی امیرکبیر، 32 (2) (1384). ## 10. حائری م.، یثربی س.ش.، ارومیه‌ای ع.، اصغری، ا.، "ویژگی‌های زمین‌شناسی مهندسی آبرفتهای درشت‌دانه و سیمانی شده تهران"، علوم زمین، 11 (47-48) (1382) 2-15. ## 11. باغبان گل‌پسند م.ر.، نیکودل م.ر.، ارومیه‌ای ع.،" بررسی تأثیر عوامل زمین‌شناسی مهندسی بر پارامترهای مرتبط با ارزیابی تجربی نشست زمین در اثر حفر تونل ابوذر، تهران"، نشریۀ زمین‌شناسی مهندسی، 10 (3) (1395). ## 12. بربریان م.، قریشی م.، ارژنگ روش ا.، مهاجر اشجعی ا. ، "پژوهش و بررسی ژرف نو زمین‌ساخت و خطر زمین‌لرزه- گسلش در گستره تهران و پیرامون"، گزارش شمارۀ 56 سازمان زمین شناسی کشور (1364). ## 13. جعفری م.، اصغری ا.، "ریزپهنه‌ندی ژئوتکنیک لرزه‌ای جنوب‌غربی تهران از دیدگاه تأثیرات ساختگاهی"، نشریۀ 3-98-77 مؤسسه بین‌المللی زلزله‌‌شناسی و مهندسی زلزله (1376). ## 14. جعفری م.، ریز هنه‌بندی ژئوتکنیک لرزه‌ای شمال تهران از دیدگاه تأثیرات ساختگاهی"، مؤسسه بین‌المللی زلزله شناسی و مهندسی زلزله (1381). ## 15. Akhtarpour A., Mortezaee M., "Dynamic response of a tall building next to deep excavation considering soil–structure interaction", Asian J Civ Eng, (2018) 1-24. ## 16. علاء‌دین ی.، طالبیان م.، آرین، م.، احمدی م. م.، "بررسی ژئوتکنیکی و پهنه‌بندی لرز‌ه‌ای آبرفت در باختر تهران"، نشریۀ علوم زمین (زمین ساخت) 94 (1394) 333-342. ## 17. اصغری ابراهیم، "تأثیر سیمانی شدن بر مقاومت برشی و تغییر شکل خاک‌های درشت‌دانه با نگرشی به آبرفت‌های تهران"، رسالۀ دکتری زمین‌شناسی مهندسی، دانشگاه تربیت مدرس، (1381). ## 18. Haeri S. M., Hamidi A., Hosseini S. M., Asghari E., Toll D. G., "Effect of cement type on the mechanical behavior of a gravely sand", Geotechnical and Geological Engineering Journal, Vol.24 (2006) 335-360. ## 19. چشمی ا.، فاخر ع.، خامه‌چیان م.، ا.، "زمین‌شناسی آبرفت‌های تهران و ارزیابی طبقه‌بندی ریبن جهت مطالعات زمین‌شناسی مهندسی"، مجلۀ علوم دانشگاه تهران، 34 (1) (1387) 47-61. ## 20. چشمی ا.، رمضان‌نژاد الیردی ر.، فاخر ع.، "توسعه طبقه‌بندی آبرفت‌های تهران بر اساس ویژگی‌های زمین‌شناسی و پارامترهای ژئوتکنیکی"، فصلنامۀ زمین‌شناسی مهندسی، 11 (1) (1397) 65-79. ## 21. شرکت مهندسی مشاور پردیسان سازه ابنیه، "گزارش جمع‌بندی مطالعات زمین‌شناسی مهندسی و ژئوتکنیک پروژه تونل و آزاد راه شهید شوشتری (مرحلۀ اول و دوم)"، (1397). ## 22. Park S. S., Choi S. G., Nam I. H., "Effect of plant-induced calcite precipitation on the strength of sand", J. Mater. Civ. Eng., Vol. 26 (2014). ## 23. Choi S., Wu S., Chu J., "Bio cementation for sand using an eggshell as calcium source: J. Geotech. Geoenviron. Eng., Vol. 142 (2016). ## 24. Lin H., Suleiman M. T.,‌ Brown D. G., Kavazanjian Jr. E., "Mechanical Behavior of Sands Treated by Microbially Induced Carbonate Precipitation", Vol. 142 (2016). ## 25. جوزانی کهن گ.، نوروزی غ.، سحابی ف. و اوجانی ح.، "مقایسۀ روش‌های شناخت کانی‌های رسی با استفاده از داده‌های آزمایشگاهی و پتروفیزیکی در یکی از میادین گازی شرق کپه‌داغ"، نشریه علمی – پژوهشی مهندسی معدن، 11 (30) (1395) 1-11. ## 26. Tchalenko J. S., Berberian M., Iranmanesh H., Bailly M., Arsovsky M., "Tectonic framework of Tehran region, geological survey of Iran", Report No. 29 (1974) 7-46. ## 27. Vita Finzi C., "Contributions to the Quaternary geology of southern Iran". G.S. of Iran. Rep. No. 47 (1979) 52. ## 28. Asghari E., Toll D. G., Haeri S. M., "Triaxial behavior of a cemented gravely sand", Tehran alluvium, Geotechnical and Geological Engineering Journal, Vol. 21 (2003) 1-28. ## 29. El May M., Souissi D., Ben Said H., Dlala M., "Geotechnical characterization of the quaternary alluvial deposits in Tunis City (Tunisia)", Journal of African Earth Sciences, vol. 108 (2015) 89-100. ## 30. Hamidi A., Yarbakhti P., "Constitutive modeling of cemented gravely sands including the effects of cement type", jeg. Vol.6 (2013) 1525-1544. ## 31. Huber H., "The Quaternary deposits of the Darya-i-Namak, Central Iran, Iranaian Oil Company", Geol. Note 51 (1960). ## 32. Dellenbach J., "Contribution a l etude geologigue de la region situeo a l est de Tehran, Iran", Fac Sci, Univ. Strasbourg (France) (1964). ## 33. Allenbach P., "Geologic and petrographic des Damavand und seiner Umgeburg (Zentral Elburz), Iran". Mitteilung Nr. 63, Geologisches Institut, ETH, Zuurich (1966). ## Shafiee A., Azadi A., "Shear-wave velocity characteristics of geological units throughout Tehran city, Iran", J. Asian Earth Sci., Vol. 29 (2007) 105-115. ## 34. Ouhadi V. R., Yong R. N., "Ettringite formation and behaviour in clayey soils", Applied Clay Science, Vol. 42 (2008) 258-265. ## 35. Hamidi A., Soleimani S., "Shear strength –dilation relation in cemented gravely sands". International Journal of Geotechnical Engineering, Vol. 6 (2012) 415-425. ## 36. Ghafghazi M., DeJong J. T., Wilson D. W., "Evaluation of Becker penetration test interpretation methods for liquefaction assessment in gravelly soils", Canadian Geotechnical Journal, Vol. 54 (2017) 1272-1283. ## 37. Santamarina J. C., Klein K., Fam M.,"Soils and waves", Wiley, Chichester, U.K (2001). ## 38. Borcherdt R., Wentworth C. M., Janssen A., Fumal T., Gibbs J., "Methodology for Predictive GIS Mapping of Special Study Zones for Strong Ground Shaking in the San Francisco Bay Region, CA", Proc. 4th Int. Conf. Seismic Zonation, (1991) 545-552. ## 39. International Conference of Building Officials, "Uniform Building Code", Whittier, CA (1997). ## 40. Building Seismic Safety Council, "NEHRP (National Earthquake Hazards Reduction Program) Recommended Provisions for the Development of Seismic Regulations for New Buildings (and Other Structures)", Washington, DC (1997). ## 41. American Society of Civil Engineers, "Minimum Design Loads for Buildings and Other Structures", ASCE/SEI 7-15, Reston, VA (2015). 42. مرکز تحقیقات ساختمان و مسکن (1395)، "آئین نامه طراحی ساختمان‌ها در برایر زلزله"، استاندارد 2800 – ویرایش چهارم. ## 43. Anbazhagan P., Neaz Sheikh M., Parihar A., "Influence of Rock Depth on Seismic Site Classification for Shallow Bedrock Regions", Natural Hazards Review, Vol. 14 (2013). ## 44. Standards Australia, "Structural design actions-earthquake actions in Australia", AS 1170.4-2007, Sydney, Australia (2007). ## 45. China Net for Engineering Construction Standardization, "Code for seismic design of buildings", GB 50011-2010, China Building Industry Press, Beijing (2010). ## 46. Bureau of Indian Standards (BIS), "Indian standard criteria for earthquake resistant design of structures", Part 1-General provisions and buildings.” BIS 1983, New Delhi, India (2002). ## 48. Eurocode 8., "Design of structures for earthquake resistance", European Committee for Standardization (2004). ##