Engineering Geology

Engineering Geology

A Finite Element Model for Simulating Flow around a Well with Helically Symmetric Perforations

Authors
Seyed Amirodin Sadrnejad
Hasan Ghasemzadeh
Ahmadali Khodaei Ardabili
Department of Civil Engineering, K.N. Toosi University of Technology, Tehran, Iran
10.18869/acadpub.jeg.12.5.159
Abstract
In a perforated well, fluids enter the wellbore through arrays of perforation tunnels. These perforations are typically distributed in a helical pattern around the wellbore. Available numerical models to simulate production flow into cased-and-perforated vertical wells have complicated boundary conditions or suffer from high computational costs. This paper presents a simple and at the same time efficient finite element model to simulate flow around a well with helically symmetric perforations. In the proposed model, by taking advantage of the symmetry, only a thickness of perforated interval containing a single perforation tunnel needs to be meshed. Angular phasing between adjacent perforations is considered by applying periodic boundary conditions on the upper and lower boundaries of the representative reservoir thickness. These boundary conditions involve periodic-pressure and periodic-velocity parts. Unlike the periodic-pressure part, the method of imposing the periodic-velocity condition within a single-variable flow problem is rather vague. In this regard, it is proved that in the proposed model, periodic-velocity condition is automatically satisfied in a weak sense. The accuracy and the computational efficiency of the proposed model are verified through comparison with available models. The model results, in terms of skin factor, are compared with the common semi-analytical model as well, and good agreement is obtained. The proposed model can readily be used as a numerical tool to study inflow of wells with helically symmetric perforations.
Keywords
Cased and perforated well
finite element method
Helical symmetry
Periodic boundary condition
Well inflow analysis
1. Zhan L., Doornbosch F., Martin A., Harvey J., Brenden G., "Perforated Completion Optimization Using a New, Enhanced and Integrated Perforating Job Design Tool," Presented at the SPE International Symposium and Exhibition on Formation Damage Control, Lafayette, Louisiana, USA, (2012).## 2. Hagoort J., "An analytical model for predicting the productivity of perforated wells", J Petrol Sci Eng. vol. 56 (2007) 199-218. ## 3. Hashemi S. M., Zamani E., Mahdian A., "Numerical simulation and performance optimization of oil well perforator", Modares Mechanical Engineering, vol. 16, no. 3, (2016) 17-26 (in Persian) ## 4. Satti R., Betancourt D., Harvey W, Zuklic S, White R, Ochsner D, Sampson T, Myers W, Gilliat J, "Beginning with the End in Mind: Shaped Charges Designed for Reservoir Conditions", Presented at the SPE Middle East Oil & Gas Show and Conference, Manama, Kingdom of Bahrain (2017). ## 5. Karakas M., Tariq S. M., "Semianalytical Productivity Models for Perforated Completions", SPE Production Engineering. vol. 6, no. 1, (1991) 73-82. ## 6. Bellarby J., "Well completion design", Developments in Petroleum Science, vol. 56, Elsevier, Hungary (2009). ## 7. Harris M. H., "The effect of perforating on well productivity," J Petrol Technol, vol. 18 (1966) 518-528. ## 8. Klotz J. A., Krueger F. F., Pye D. S., "Effect of perforating damage on well productivity", J Petrol Technol, vol. 29, no. 2, (1974) 1303-1314. ## 9. Locke S., "An Advanced Method for Predicting the Productivity Ratio of a Perforated Well", J Petrol Technol, vol. 33, (1981) 2481-2488. ## 10. Dogulu Y. S., "Modeling of Well Productivity in Perforated Completions", Presented at the SPE Eastern Regional Meeting, Pittsburgh, Pennsylvania, USA, (1998). ## 11. Ansah J., Proett M. A., Soliman M. Y., "Advances in Well Completion Design: A New 3D Finite-Element Wellbore Inflow Model for Optimizing Performance of Perforated Completions", Presented at the SPE International Symposium and Exhibition on Formation Damage Control, Lafayette, Louisiana (2002). ## 12. Jamiolahmady M., Danesh A., Sohrabi M., Ataei R., "Gas condensate flow in perforated region", SPE Journal, vol. 12, no. 1, (2007) 89-99. ## 13. Byrne M., Jimenez M. A., Chavez J. C., "Predicting Well Inflow Using Computational Fluid Dynamics-Closer to the Truth?", Presented at the SPE European Formation Damage Conference, Scheveningen, The Netherlands, (2009). ## 14. Sun D., Li B., Gladkikh M., Satti R., Evans R., "Comparison of Skin Factors for Perforated Completions Calculated with Computational-Fluid-Dynamics Software and the Karakas-Tariq Semianalytical Model", SPE Drilling & Completion, vol. 28, no, 1, (2013) 21-33. ## 15. Volonte G., Scarfato F., Brignoli M., "sand prediction: a practical finite-element 3d approach for real field applications," SPE Production & Operations, vol. 28, no. 1, (2013) 95-108. ## 16. Wang H., Cardiff P., Sharma M. M., A 3-d poro-elasto-plastic model for sand production around open-hole and cased & perforated wellbores," Presented at the 50th US Rock Mechanics / Geomechanics Symposium, Houston, Texas, USA, (2016). ## 17. Segal G., Vuik K., Kassels K., "On the implementation of symmetric and antisymmetric periodic boundary conditions for incompressible flow," Int. J. Numer. Meth. Fluids. vol. 18, (1994) 1153-1165. ## 18. Li S. "On the nature of periodic traction boundary condition in micromechanical FE analyses of unit cells", IMA J. Appl. Math., vol. 77, (2012) 441-450. ## 19. Yildiz T., "Productivity of Selectively Perforated Vertical Wells", Presented at the SPE International Oil and Gas Conference and Exhibition in China, Beijing, China, (2000). ## 20. Xia Z., Zhang Y., Ellyin F., "A unified periodical boundary conditions for representative volume elements of composites and applications", Int J Solids Struct., vol. 40, (2003) 1907-1921. ## 21. Tyrus J. M., Gosz M., DeSantiago E., "A local finite element implementation for imposing periodic boundary conditions on composite micromechanical models", Int J Solids Struct., vol. 44, (2007) 2972-2989. ## 22. Reddy J. N., "An Introduction to the Finite Element Method", 3rd ed., Singapore. McGraw-Hill. (2006). ## 23. Zienkiewicz O. C., Taylor R. L., Zhu J. Z, "The Finite Element Method: Its Basis and Fundamentals", 7th ed, UK, Elsevier Butterworth-Heinemann (2013). ## 24. Nguyen V.D., Bechet E., Geuzaine L., Noels L., "Imposing periodic boundary condition on arbitrary meshes by polynomial interpolation", Electrical Engineering, vol. 55, (2011) 390-409. ## 25. Sandstom C., Larsson F., Runesson K., "Weakly periodic boundary conditions for the homogenization of flow in porous media", Adv Model Simul Eng Sci., vol. 2, no. 12, (2014) 1-24. ## 26. Brooks J.E., "A Simple Method for Estimating Well Productivity", Presented at the SPE European Formation Damage Conference, The Hague, The Netherlands, (1997). ## 27. Yildiz T., "Assessment of Total Skin Factor in Perforated Wells", SPE Reservoir Evaluation & Engineering, vol. 9. no. 1, (2006) 62-76. ## 28. Jamiolahmady M., Mahdiyar H., Ghahri P., Sohrabi M., "A new method for productivity calculation of perforated wells in Gas condensate reservoirs", J Petrol Sci Eng, vol. 77, (2011) 263-273. ## 29. Dake L. P., "Fundamentals of Reservoir Engineering", Elsevier Science, Netherlands (1983). ##