Engineering Geology

Engineering Geology

Evaluation of the Cause of Squeezing Phenomenon in Tunnels on the Basis of Observed Microstructure in Salt Rock

Authors
Hadiseh Mansouri1
Rassoul Ajalloeian
Alireza Nadimi
Department of Geology, Faculty of Sciences, University of Isfahan
10.18869/acadpub.jeg.13.3.511
Abstract
Introduction

Generally, in engineering geology physical and mechanical properties of rocks are investigated in macroscopic scale, and less attention is paid to investigate the texture and microstructure developing in rock during deformation. Salt rock, as a best example of ductile rocks, has attracted the attention of many researchers. Compared to silicate rocks, salt rock exhibits extensively ductile behavior at even low temperature and pressure. In micro-tectonics, salt is important, because of it is useful as an analogue material for understanding the microstructural processes and textural development in silicate rocks. Deformed salt rock can display microstructures developed in silicate rocks at high pressures and temperatures. Regarding the similarity between microstructures of salt rock and silicate rocks, investigation of microstructure and deformation mechanism in salt rock can be helpful in understanding the main cause of the squeezing phenomenon in tunnels.

One of the effective factors on squeezing phenomenon is the structures and microstructures of rock. Rock mass classifications that contain rock mass structures are used in the predicting methods. But, so far, no attention has been paid to the role of rock microstructure in predicting the squeezing phenomenon.

This study is aimed to identify deformation mechanisms occurring in microscopic scale in rocks and lead to tunnel convergent in large scale. To achieve this goal, the microstructures in a naturally deformed Late Pre-Cambrian to Early Cambrian Hormuz salt rock from the active Deh Kuyeh salt fountain in Fars province were investigated using Electron Backscatter Diffraction (EBSD).

Materials and Methods

Deh Kuyeh salt diapir was located at about 27 km NE of Lar city. Salt samples were taken from top of the east and west glaciers (S1 and S2) and from the middle part of diapiric stem (sample S3). Raw samples were first cut dry into slabs (approximately 3´2 ´1 cm). Thin sections were prepared following the procedure of Schleder and Urai (2005) and Urai et al. (1987).

Halite crystallographic orientation data were collected using a Zeiss SIGMAVP FEGSEM. EBSD patterns were collected using an accelerating voltage of 30 kV, beam current of ~ 100 nA and a working distance of about 30 mm. Oxford instruments AZTEC software was used for data acquisition. EBSD large step size (50 mm) mapping was used to examine the overall microstructure in each sample. EBSD data were processed using HKL Channel 5 software.

Results and Discussion

All samples showed relatively similar microstructures. Samples comprise a small number of large grains in a matrix of smaller grains. Most grains were irregular in shape with lobate boundaries and internal distortion. Microstructural study revealed that the ductile flow of the salt was accommodated by dislocation creep and dynamic recrystallization. Salt grains show lattice distortion and a prevalence of low-angle boundaries that are evidence for dislocation creep and recovery processes. Misorientation analysis suggests that (110) <110> and (111) <110> slip systems are responsible for crystal plastic deformation of salt grains. Schmid factor analysis showed that stresses acting on inclined directions lead to the maximum activity of these slip systems.

The observed microstructures in the salt are comparable with the microstructures presented for schist samples from Himalaya region. The rock along Himalaya main trusts also showed evidence of dislocation creep and development of crystallographic preferred orientation. Hence, this article suggests that the rock type and its microstructures are the most important factors in occurrence of tunnel convergent.

Conclusions

This article proposes that deformation mechanisms occurring in micro-scale control the rock behavior in large scale. All rocks can behave as a ductile material depending on the temperature and pressure. In intrinsically ductile rocks like salt rock, presence of many active slip systems facilitates rock deformation under lower pressures and temperatures than silicate rocks. High tectonic stresses in shear zones lead to development of a strong shape preferred orientation and crystal preferred orientation in rocks. These microstructures facilitate rock deformation under stresses exiting in tunnels. It can be said that rock type and tectonic history of the area play the most important role in occurrence of squeezing phenomenon. Other factors such as current stress system in the area control deformation speed in tunnel. It seems investigating microstructures of rocks from tunnel route before and after excavation can be effective in identifying places with high possibility of squeezing.
Keywords
Squeezing
microstructures in rock
dislocation creep
Electron backscatter diffraction method
1. Bestmann M., Piazolo S., Spiers C. J. Prior D. J., "Microstructural evolution during initial stages of static recovery and recrystallization: new insights from in-situ heating experiments combined with electron backscatter diffraction analysis", Journal of Structural Geology, Vol. 27 (2005) 447-457.##. 2. Piazolo S., Bestmann M., Prior D. Spiers C., "Temperature dependent grain boundary migration in deformed-then-annealed material: observations from experimentally deformed synthetic rocksalt", Tectonophysics, Vol. 427 (2006) 55-71. ## 3. Závada P., Desbois G., Schwedt A., Lexa O. Urai J.L., "Extreme ductile deformation of fine-grained salt by coupled solution-precipitation creep and microcracking: Microstructural evidence from perennial Zechstein sequence (Neuhof salt mine, Germany)", Journal of Structural Geology, Vol. 37 (2012) 89-104. ## 4. Shrestha G. L., "Stress induced problems in Himalayan tunnels with special reference to squeezing, Doctoral Thesis, Norwegian University of Science and Technology, Trondheim, Norway.", (2006(.## 5. Carranza-Torres C. Fairhurst, C., "The elasto-plastic response of underground excavations in rock masses that satisfy the Hoek–Brown failure criterion", International Journal of Rock Mechanics and Mining Sciences, Vol. 36 (1999) 777-809. ## 6. Goel R., Jethwa J., Paithankar A., "Tunnelling through the young Himalayas-a case history of the Maneri-Uttarkashi power tunnel", Engineering Geology, Vol. 39 (1995) 31-44. ## 7. Hoek E. Marinos P., "Predicting tunnel squeezing problems in weak heterogeneous rock masses", Tunnels and tunnelling international, Vol. 32 (2000) 45-51. ## 8. Jethwa J., Singh B., Singh B., "28 Estimation of ultimate rock pressure for tunnel linings under squeezing rock conditions-a new approach. in Design and Performance of Underground Excavations: ISRM Symposium-Cambridge, UK, 3–6 September 1984, Thomas Telford Publishing (1984). ## 9. Singh B., Jethwa J., Dube A., Singh B., "Correlation between observed support pressure and rock mass quality", Tunnelling and Underground Space Technology, Vol. 7 (1992) 59-74. ## 10. Aydan Ö., Akagi T. Kawamoto T., "The squeezing potential of rocks around tunnels; theory and prediction", Rock Mechanics and Rock Engineering, Vol. 26 (1993) 137-163. ## 11. Panthi K. Nilsen B., "Uncertainty analysis of tunnel squeezing for two tunnel cases from Nepal Himalaya", International Journal of Rock Mechanics and Mining Sciences, Vol. 44 (2007) 67-76. ## 12. Shamsoddin M. S. Maarefvand P., "Engineering geological study of NWCT tunnel in Iran with emphasis on squeezing problems", Indian Geotechnical Journal, Vol. 44 (2014) 357-369. ## 13. Ajalloeian R., Moghaddam B., Azimian A., "Prediction of Rock Mass Squeezing of T4 Tunnel in Iran", Geotechnical and Geological Engineering, Vol. 35 (2017) 747-763. ## 14. Yassaghi A. Salari-Rad H., "Squeezing rock conditions at an igneous contact zone in the Taloun tunnels, Tehran-Shomal freeway, Iran: a case study", International Journal of Rock Mechanics and Mining Sciences, Vol. 42 (2005) 95-108. ## 15. Sulem J., Subrin D.,., Monin N., Lascols, J., "Anisotropic closure in squeezing rocks: the example of Saint-Martin-la-Porte access gallery", Rock mechanics and rock engineering, Vol. 46 (2013) 231-246. ## 16. Mezger F., Anagnostou G. Ziegler H.-J., "The excavation-induced convergences in the Sedrun section of the Gotthard Base Tunnel", Tunnelling and Underground Space Technology, Vol. 38 (2013) 447-463. ## 17. Pennock G., Drury M., Peach C., Spiers C., "The influence of water on deformation microstructures and textures in synthetic NaCl measured using EBSD", Journal of structural geology, Vol. 28 (2006) 588-601. ## 18. Prior D. J., Wheeler J., Peruzzo L., Spiess R. Storey C., "Some garnet microstructures: an illustration of the potential of orientation maps and misorientation analysis in microstructural studies", Journal of Structural Geology, Vol. 24 (2002) 999-1011. ## 19. Wheeler J., Prior D., Jiang Z., Spiess R., Trimby P., "The petrological significance of misorientations between grains", Contributions to Mineralogy and Petrology, Vol. 141 (2001) 109-124. ## 20. جهانی س.،"تکتونیک نمک، چین‌خوردگی و گسلش در زاگرس و خلیج فارس"، مجموعه مقالات سی امین گردهمایی علوم زمین (1390). ## 21. Jahani S., Callot J.-P., Letouzey J., Laotte D., "The eastern termination of the Zagros Fold-and-Thrust Belt, Iran: Structures, evolution, and relationships between salt plugs, folding, and faulting", Tectonics, Vol. 28 (2009). ## 22. Talbot C. J., "Extrusions of Hormuz salt in Iran", Geological Society, London, Special Publications, Vol. 143 (1998) 315-334. ## 23. مرادی س.، "استفاده از داده های استر در تحلیل ارتباط سنگ-شناسی و پتانسیل‌های معدنی گنبد نمکی دهکویه، شمال شرقی لار"، پایان‌نامۀ کارشناسی ارشد، دانشگاه شیراز (1393)، 140. ## 24. Bosák P., "Salt plugs in the eastern Zagros, Iran: results of regional geological reconnaisance: Institute of Geology, Academy of Sciences of the Czech Republic (1998). ## 25. Jahani S., Callot J.-P., de Lamotte D. F., Letouzey J., Leturmy P., "The salt diapirs of the eastern Fars province (Zagros, Iran): A brief outline of their past and present, in Thrust Belts and Foreland Basins", (2007) Springer 289-308. ## 26. معماریان ح.، "زمین‌شناسی ساختاری، مؤسسه انتشارات دانشگاه تهران"، تهران، چاپ دوم، (1388) 842 . ## 27. Passchier C. Trouw R., "Microtectonics, Second, Revisited and Enlarged Edition", Springer-Verlag, Berlin Heidelberg (2005)366. ## 28. محجل م.، "میکروتکتونیک، ترجمۀ کتاب Microtectonics نوشتۀ Passchier, C. W. & Trow, R, A. J.,"، مرکز نشر آثار علمی، دانشگاه تربیت مدرس، تهران، چاپ اول، (1388) 742 . ## 29. Schleder Z., Urai J. L., "Microstructural evolution of deformation-modified primary halite from the Middle Triassic Röt Formation at Hengelo, The Netherlands", International Journal of Earth Sciences, Vol. 94 (2005) 941-955. ## 30. Urai J. Spiers C., "The effect of grain boundary water on deformation mechanisms and rheology of rocksalt during long-term deformation", in Proc. 6th Conf. Mech. Beh. of Salt (2007). ## 31. Schléder Z., Urai J. L., "Deformation and recrystallization mechanisms in mylonitic shear zones in naturally deformed extrusive Eocene-Oligocene rocksalt from Eyvanekey plateau and Garmsar hills (central Iran)", Journal of Structural Geology, Vol. 29 (2007) 241-255. ## 32. Trimby P. W., Drury M. R., Spiers C. J., "Recognising the crystallographic signature of recrystallisation processes in deformed rocks: a study of experimentally deformed rocksalt", Journal of Structural Geology, Vol. 22 (2000) 1609-1620. ## 33. Trimby P. W., Prior D. J., Wheeler J., "Grain boundary hierarchy development in a quartz mylonite", Journal of Structural Geology, Vol. (1998) 917-935. ## 34. Reusch E., "Über eine besondere Gattung von Durchgängen im Steinsalz und Kalkspath", Annalen der Physik, Vol. (1867) 441-451. ## 35. Wang Z., "Mechanical Properties of Crystalline Materials", Material Science and Engneering, Vol. 208 (1966). ## 36. Barreiro J. G., Lonardelli I., Wenk H., Dresen G., Rybacki E., Ren Y. Tomé C., "Preferred orientation of anorthite deformed experimentally in Newtonian creep", Earth and Planetary Science Letters, Vol. 264 (2007) 188-207. ## 37. Elyaszadeh R., Sarkarinejad K. Prior D. J., "Intracrystalline deformation of garnet, wollastonite and pectolite grains during development of a crenulation cleavage in the sheared skarn", Journal of Structural Geology, 101 (2017) (15-25). ## 38. Drury M. R., Urai J. L., "Deformation-related recrystallization processes", Tectonophysics, Vol. 172 (1990) 235-253. ## 39. Wenk H., Canova G., Molinari A., Mecking H., "Texture development in halite: comparison of Taylor model and self-consistent theory", Acta metallurgica, Vol. 37 (1989) 2017-2029. ## 40. Talbot C., Alavi M., "The past of a future syntaxis across the Zagros", Geological Society, London, Special Publications, Vol. 100 (1996) 89-109. ## 41. Callot J. P., Jahani S., Letouzey J., "The role of pre-existing diapirs in fold and thrust belt development", Thrust belts and foreland basins, Vol. 16 (2007) 309-325. ## 42. Shea W. T. Kronenberg A. K., "Rheology and deformation mechanisms of an isotropic mica schist", Journal of Geophysical Research: Solid Earth, Vol. 97 (1992) 15201-15237. ## 43. نوربهشت ا.، "مقدمه‌‌ای بر بلورشناسی"، انتشارات دانشگاه اصفهان، اصفهان، چاپ چهارم، (1383) 233. ## 44. Brander L., Svahnberg H. Piazolo S., "Brittle-plastic deformation in initially dry rocks at fluid-present conditions: transient behaviour of feldspar at mid-crustal levels", Contributions to Mineralogy and Petrology, Vol. 163 (2012) 403-425. ## 45. Fukuda J.-i., Okudaira T., Satsukawa T. Michibayashi K., "Solution-precipitation of K-feldspar in deformed granitoids and its relationship to the distribution of water", Tectonophysics, Vol. 532 (2012) 175-185. ## 46. Menegon L., Pennacchioni G., Heilbronner R. Pittarello L., "Evolution of quartz microstructure and c-axis crystallographic preferred orientation within ductilely deformed granitoids (Arolla unit, Western Alps)", Journal of Structural Geology, Vol. 30 (2008) 1332-1347. ## 47. Hickman S. H., Evans B., "Experimental pressure solution in halite: the effect of grain/interphase boundary structure", Journal of the Geological Society, Vol. 148 (1991) 549-560. ## 48. Swannell N., Palmer M., Barla G. Barla M., "Geotechnical risk management approach for TBM tunnelling in squeezing ground conditions", Tunnelling and Underground Space Technology, Vol. 57 (2016) 201-210. ## 49. Wang C. Bao L., "Predictive analysis of stress regime and possible squeezing deformation for super-long water conveyance tunnels in Pakistan", International Journal of Mining Science and Technology, Vol. 24 (2014) 825-831. ##