بررسی استاتیکی و شبه استاتیکی تنش‌‌ها و تغییر مکان‌‌های سد خاکی در مدل‌‌های تک‌لایه و لایه‌‌بندی شده پایداری سدهای خاکی در شرایط تراوش پایدار به‌ویژه در حین زلزله بسیار مهم است. تحلیل‌‌های عددی به‌وسیلۀ نرم‌‌افزار نیازمند مدل‌‌سازی صحیح و واقع‌‌بینانۀ مراحل ساخت است. از آن‌‌جا‌که سدهای خاکی در لایه‌‌های مختلف ساخته می‌‌شوند، به‌منظور حصول طراحی معقول، این شرایط باید در مدل‌‌سازی نرم‌‌افزاری نیز لحاظ شود. در این پژوهش، یک سد خاکی با استفاده از نرم‌‌افزار PLAXIS مدل شده و اثرات تعداد و شکل لایه‌‌ها در شرایط خشک و هم‌چنین تراوش بررسی شده است. نتایج حاصل از تحلیل‌‌های استاتیکی و شبه‌‌استاتیکی نشان می‌‌دهد که مدل‌‌سازی سد خاکی در لایه‌‌بندی‌‌های مختلف اثرات مهمی بر تنش‌‌های برشی و تغییر مکان‌‌های افقی بدنۀ سد دارد. برای نمونه تغییر مکان‌‌های افقی و تنش‌‌های برشی در مدل‌‌های لایه‌‌بندی شده دست کم به‌ترتیب به میزان 50 و 17 درصد نسبت به مدل تک لایه افزایش می‌‌یابند. با توجه به نتایج به‌دست آمده می‌‌توان گفت مدل‌‌سازی سد خاکی به‌صورت لایه‌‌بندی شده و ترجیحاً در در لایه‌‌های شیب‌دار معقول‌‌تر است. http://jeg.khu.ac.ir/article-1-2722-fa.pdf 2017-11-01 1 22 10.18869/acadpub.jeg.11.3.1 سد خاکی توزیع تنش تغییر مکان مدل لایه‌‌بندی شده تحلیل شبه استاتیکی Static and Pseudo Static Study of Stress and Displacement of Earth-Fill Dam Using Layered and Single-Layer Models Earth-fill dams stability in steady state seepage condition is very important, especially during earthquakes. Numerical software analyses require accurate and realistic modeling of construction stages. Since earth-fill dams are constructed in different layers, so these conditions should be considered in software modeling to achieve a reasonable design. In this study, an earth-fill dam is modeled in PLAXIS software and the effects of the number and shape of layers are studied in dry and steady-state conditions. Obtained results in static and pseudo-static analyses show that modeling of earth-fill dams with different layers has significant effects on shear stresses and horizontal displacements. For example, horizontal displacements and shear stresses, increase at least 50% and 17% respectively, in comparison with single layer models. According to the obtained results, it can be mentioned that modeling of an earth-fill dam in the layered model and rather in inclined layers are more reasonable http://jeg.khu.ac.ir/article-1-2722-en.pdf 2017-11-01 1 22 10.18869/acadpub.jeg.11.3.1 Earth-Fill dam Stress distribution Displacement Layered model Pseudo static analysis Behrouz Ahmadpour 1 AUTHOR Masoud Amel Sakhi 2 AUTHOR
تأثیر خاکستر پوسته برنج روی مقاومت فشاری محدود نشده و پتانسیل تورم خاک‌های رسی تثبیت شده با آهک در مجاورت سولفات  مهندسان ژئوتکنیک در بسیاری از پروژه‌ها با خاک‌های رسی دارای مقاومت کم و یا تورم زیاد مواجه می­شوند. تثبیت خاک یکی از راه‌های مقابله با مشکلات این نوع خاک‌ها است. آهک و سیمان متداول‌ترین مواد شیمیایی در تثبیت خاک‌ها خصوصاً خاک‌های رسی هستند. اگر در خاک رس تثبیت شده با آهک، سولفات وجود داشته باشد یا خاک در معرض سولفات قرار گیرد مشکلاتی از جمله کاهش مقاومت و افزایش تورم خاک رس بوجود می­آید. علت این پدیده، واکنش شیمیایی بین کانی‌های خاک رس، آهک و سولفات است که باعث به‌وجود آمدن کانی­های ایترینگایت و تاماسایت در خاک می­شود. استفاده از پسماندهای صنعتی موجود در کشور همانند خاکستر پوستۀ برنج[1] در عملیات تثبیت خاک می‌تواند توجیه قتصادی داشته باشد. خاکستر پوستۀ برنج شامل مقادیر زیادی سیلیکا با سطح ویژه بالاست که برای فعال­سازی واکنش بین آهک و خاک مناسب است. در این تحقیق از آهک و خاکستر پوسته برنج برای تثبیت خاک رس گچ‎دار استفاده می‎شود و مقاومت فشاری محدود نشده و پتانسیل تورم خاک رس تثبیت شده ارزیابی می‌شود. سولفات در ساحتار نمونۀ خاک موجود است. نتایج به‌دست آمده از این تحقیق نشان‌دهندۀ تأثیر مثبت خاکستر پوستۀ برنج بر افزایش مقاومت و کاهش تورم خاک رس گچ دار تثبیت شده با آهک است. از نقطه نظر تأمین مقاومت، مشخصات تورمی و اقتصاد طرح، اضافه کردن حدود 6-8% آهک و 8-10%  خاکستر پوستۀ برنج برای تثبیت خاک رس پیشنهاد می‌شود.    * نویسنده مسئول         mhbazyar@mail.yu.ac.ir [1]. Rice Husk Ash http://jeg.khu.ac.ir/article-1-2721-fa.pdf 2017-11-01 23 52 10.18869/acadpub.jeg.11.3.23 خاک رس گچ‎دار مقاومت فشاری محدود نشده پتانسیل تورم تثبیت خاک خاکستر پوستۀ برنج  The Effect of Rice Husk Ash on Mechanical Properties of Clayey Soils Stabilized with Lime in the Presence of Sulphate  Geotechnical engineers, in many cases face with low strength or high swelling potential of clayey soils. Stabilization methods are used to improve the mechanical properties of this type of soils. Lime and cement are the most popular materials used in chemical stabilization of clayey soils. If sulphate exists in the stabilized clayey soil with lime, or if soil is exposed to sulphates, problems such as strength reduction and swelling increase will occur. Reuse of industrial residual such as Rice Husk Ash (RHA) can be beneficial from the economy point of view. RHA includes a proper amount of silica with high specific surface area which is very suitable for activating the reaction between the soil and lime. In this paper, chemical stabilization of gypsum clays using lime and RHA is addressed Sulphates exist in the constitution of the soil. Unconfined compression strength and swelling potentials of the stabilized soil are evaluated. The results of this study indicate that RHA has positive impacts on improving mechanical properties of the gypsum clays stabilized with lime. From the view point of strength and swelling characteristics, and economy, addition of 6–8% lime and 8-10% RHA as an optimum amount is recommended. http://jeg.khu.ac.ir/article-1-2721-en.pdf 2017-11-01 23 52 10.18869/acadpub.jeg.11.3.23 Gypsum clay Unconfined Strength Swelling potential Stabilization Rice Husk Ash. Mohammad Hossin Bazyar 1 AUTHOR Mostafa Ebrahimi 2 AUTHOR Mehdi Zamani Lenjani 3 AUTHOR Masood Makarchian 4 AUTHOR
فشار فعال لرزه‌ای ناشی از خاکریز مسلح ژئوسنتتیکی با عرض کم بر رویۀ صلب در دیوارهای خاک مسلح ژئوسنتتیکی با عرض کم، یک دیوار پایدار پشتی در فاصلۀ کمی از رویۀ دیوار وجود دارد به‌گونه­ای‌که فضای کافی برای امتداد دادن مسلح کننده با طول کافی وجود ندارد. در این‌حالت احتمال واژگونی دیوار حائل بالاخص تحت بارهای لرزه­ای افزایش می­یابد. برای افزایش پایداری دیوار، مسلح کننده­ها را می­توان به دیوار پایدار پشتی متصل کرد. روش دیگر، استفاده از رویۀ بتنی در جاریز برای تمام ارتفاع دیوار است تا فشار خاک با عملکرد مشترک مقاومت بیرون‌کشیدگی مسلح‌کننده­ها و مقاومت خمشی رویۀ دیوار تحمل شود. از سؤال‌های اساسی در مورد این نوع دیواره‌ها، میزان سهمی از فشار خاک است که به‌وسیلۀ رویۀ بتنی تحمل می­شود. در این تحقیق، فشار فعال لرزه‌ای ناشی از خاکریز مسلح با عرض کم بر رویۀ صلب با استفاده از روی‌کرد تعادل حدی و روش قطعات افقی برآورد شده است. برای این منظور فرض شده است که سطح لغزش بحرانی به‌صورت خطی از پای دیوار تا سطح پایدار پشتی امتداد یافته و سپس روی سطح پشتی تا سطح خاکریز ادامه می­یابد. تأثیر پارامترهای مختلف مانند نسبت عرض به ارتفاع دیوار بررسی شده است. نتایج به‌دست آمده بیان‌گر آن است که فشار وارد بر رویۀ در قسمت­های فوقانی دیوار طبق رابطۀ مونونوبه-اوکابه افزایش می­یابد ولی در قسمت­های تحتانی، روند گراف عوض شده و مقدار فشار وارده بر دیوار کاهش می­یابد تا به مقدار صفر در پای دیوار برسد. نتایج آنالیزها نشان می­دهد که فشار وارده بر رویۀ دیوار با کاهش عرض خاکریز، افزایش می­یابد. http://jeg.khu.ac.ir/article-1-2720-fa.pdf 2017-11-01 53 80 10.18869/acadpub.jeg.11.3.53 دیوار خاک مسلح ژئوسنتتیکی خاکریز با عرض کم نمای صلب فشار لرزه‌ای خاک روش قطعات افقی. Seismic Active Earth Pressure of Narrow Geosynthetic-Reinforced Backfill on Rigid Facing In the narrow geosynthetic-reinforced retaining walls a stable rear wall exists in a short distance and so there is no enough space to extend appropriate length of reinforcements. In this case, the probability of overturning of retaining wall increases especially when subjected to earthquake loading. To increase the stability of the wall, reinforcements may be connected to the stable rear surface. Alternative solution is the utilization of full-height cast in-place concrete facing in order to resist the earth pressure by combined actions of reinforcements pullout capacity and facing flexural rigidity. One of the main questions about this type of walls is the portion of earth pressure resisted by the facing. In this study, the seismic earth pressure of narrow geosynthetic-reinforced backfill on rigid facing was evaluated using limit equilibrium approach and horizontal slices method. The critical failure surface was assumed to extend linearly from the wall toe to the rear surface and then moves along the interface of the backfill and rear surface up to the backfill surface. The effects of various parameters such as wall aspect ratio have been investigated. The obtained results show that the applied soil pressure on wall facing will be increased with depth in the upper part of the wall according to the Mononobe-Okabe equation, but its pattern is inversed in the lower part of the wall and it decreases until it reaches to zero at the wall toe. The results of analyses indicate that the attracted soil thrust by the facing increases with lessening of backfill width. http://jeg.khu.ac.ir/article-1-2720-en.pdf 2017-11-01 53 80 10.18869/acadpub.jeg.11.3.53 Geosynthetic-reinforced soil wall Narrow backfill Full-height rigid facing Seismic earth pressure Horizontal slices method. Fariborz Dehghani 1 AUTHOR Hadi Shahir 2 AUTHOR Ali Ghanbari 3 AUTHOR
تغییر شکل و مقاومت ناهم‌سانگردی اسلیت‌های آهکی در آزمون‌های برزیلی ناهم‌سانگردی یاآنیزوتروپی در تغییر رفتار مهندسی سنگ نقش مهمی دارد.اسلیت‌ها به‌عنوان سنگ‌های دارای ناهم‌سانگردی از دیرباز برای سقف شیروانی، کفپوش‌ها و  به‌عنوان منابع قرضه استفاده می‌شوند. اسلیت‌ها­ی بررسی شده در این پژوهش آهکی است و بافت پورفیرو-لپیدوبلاستیک دارند. در این بررسی برای تعیین نقش ناهم‌سانگردی بر مقاومت کششی و الگوی شکستگی، از دو متغیر ψ (زاویۀ محور مغزه‌گیری نسبت به سطح فولیاسیون) و β (زاویۀ بین محور بارگذاری و امتداد فولیاسیون) در آزمایش برزیلی استفاده شد. زوایا هر 15 درجه انتخاب شده‌اند بدین معنا که برای هم ψ و هم β، هفت زاویه 0، 15، 30، 45، 60، 75 و 90 درجه تعریف شده است (برای هر نمونه 43 حالت ممکن وجود دارد). برای نام‌گذاری و بررسی الگوی­های شکستی، 11 الگو پیشنهاد شده است. متوسط مقاومت شکست برای سه ایستگاه تنوع 21/3 تا 94/20 مگاپاسکال را نشان داد. بر اساس نتایج متوسط مقاومت کششی با دانسیته رابطۀ مستقیم دارد. با مقایسه داده‌های آزمون کشش برزیلی، مقاومت کششی در حالت اشباع 8/30 درصد کم‌تر از حالت خشک است. از طرفی طول شکستگی در مقابل ψ و β رابطه عکس نشان داده است. متوسط مقاومت کششی و شاخص ناهم‌سانگردی نشان دادند که تأثیر زاویه جهت‌گیری(ψ) بیش‌تر از زاویه بارگذاری-فولیاسیون (β) است. http://jeg.khu.ac.ir/article-1-2719-fa.pdf 2017-11-01 81 102 10.18869/acadpub.jeg.11.3.81 ناهم‌سانگردی اسلیت آزمون برزیلی الگوی شکستگی مقاومت کششی Deformation and strength anisotropy of calcareous slates under Brazilian tests Rock anisotropy plays an important role in engineering behavior of rocks. Slates are anisotropic rocks which have long been used for gable roof, floor tiles, borrow materials, and other purposes. The slates studied in this research are calcareous and have a porphyro-lepidoblastic texture. To determine the role of the anisotropy on the tensile strength and fracture pattern, two variables including ψ (the core axis angle to foliation) and β (the angle between the axis of loading and foliation) in the Brazilian tests were used. The angles were selected at 15° intervals. Thus, for both ψ and β, seven angles of 0˚, 15˚, 30˚, 45˚, 60˚, 75˚, and 90˚ were selected (i.e., there are 43 possible modes). In order to name and examine the failure pattern, 11 models were proposed. The average value of the failure strength for the three stations varies from 3.21 MPa to 20.94 MPa. Based on the obtained results, there is a direct relation between the average tensile strength and density. A comparison between Brazilian test data under dry and saturation conditions shows that the saturated Brazilian tensile strength is 30.8% less than the dry Brazilian tensile strength. Moreover, the changes in fracture length with the changes in ψ and β indicate an inverse relation. Eventually, the average of tensile strength (σt) and strength anisotropy index (Ia) demonstrates that the influence of orientation angle (ψ) is much larger than that of foliation-loading angle (β).   http://jeg.khu.ac.ir/article-1-2719-en.pdf 2017-11-01 81 102 10.18869/acadpub.jeg.11.3.81 Anisotropy Slate Brazilian test Fracture pattern Tensile strength Mohammad Hosein Ghobadi 1 AUTHOR Paria Behzadtabar 2 AUTHOR
مکان یابی محل دفن پسماندهای شهری: مطالعۀ موردی در اردبیل لندفیل به‌عنوان ارزان‌ترین روش برای دفع پسماندهای جامد شهری شناسایی شده است به شکلی که رایج‌ترین روش استفاده شده است. مکان‌یابی محل دفن فرآیندی پیچیده است که دربردارندۀ پارامترهای اجتماعی، زیست‌محیطی، اقتصادی و قوانین دولتی است. هدف از این پژوهش یافتن محل‌های مناسب برای دفن پسماندهای شهری در اردبیل با استفاده از روش MCDM و بررسی‌های میدانی است. در مرحلۀ اول که با استفاده از پیوستگی GIS+AHP انجام گرفت، مناطق ممنوعه شناسایی شده و با در نظر گرفتن حریم حذف شدند. سپس معیارهای دیگر به چهار زیر معیار طبقه‌بندی شدند و بعد از وزن دهی و نمره‌دهی معیارها و زیرمعیارها با استفاده از روش AHP، نقشه‌ها در محیط GIS هم‌پوشانی شدند. حذف مناطق حریم از نقشه تناسب نشان داد 4 درصد منطقه که دربردارندۀ 12 محل است مناطق مستعد برای ساخت لندفیل هستند. در مرحلۀ دوم از 12 محل بررسی میدانی انجام گرفت و 8 محل حذف شده و 4 محل به‌عنوان محل‌های مناسب معرفی شد. در پایان به‌منظور انتخاب مناسب‌ترین محل از بین این 4 محل، گزینه‌ها از نقطه نظرات ملاحظات زیست‌محیطی و اجتماعی- اقتصادی با دقت با روش TOPSIS ارزیابی شدند. در نتیجه محل 6 به‌عنوان مناسب‌ترین محل معرفی شد. http://jeg.khu.ac.ir/article-1-2718-fa.pdf 2017-11-01 103 134 10.18869/acadpub.jeg.11.3.103 اردبیل؛ مکان یابی لندفیل؛ GIS؛ MCDM Landfill Siting for Municipal Waste: A Case Study in Ardebil http://jeg.khu.ac.ir/article-1-2718-en.pdf 2017-11-01 103 134 10.18869/acadpub.jeg.11.3.103 Kobra Jafari 1 AUTHOR Naser Moghaddas 2 AUTHOR Alireza Mazloumi Bajestani 3 AUTHOR Azam Ghazi 4 AUTHOR
هم‌بستگی بین پارامترهای طیفی زمین‌لرزه‌ها و شدت آسیب در قاب‌های بتن مسلح در چند دهۀ اخیر، پژوهش‌گران بسیاری ارزیابی آسیب سازه‌ها پس از یک رخداد لرزه‌ای را بررسی کرده‌اند. برای ارزیابی آسیب سازه‌ها تحت یک زمین‌لرزه، بررسی هم‌بستگی بین پارامترهای زمین‌لرزه و آسیب سازه‌ها اهمیت زیادی دارد. محققان پارامترهای لرزه‌ای متعددی برای توصیف زمین‌لرزه تعریف کره‌اند. از آن‌جا که پارامترهای طیفی زمین‌لرزه اطلاعات متنوعی پیرامون حرکت زمین دربر دارند، یک زمین‌لرزه را به‌درستی توصیف می‌کنند. هم‌چنین شاخص‌های خسارت متنوعی برای سنجش آسیب سازه‌ها یا تعیین آسیب‌پذیری آن‌ها نسبت به یک‌دیگر، پیشنهاد شده است. شاخص آسیب پارک-انگ یکی از بهترین شاخص‌ها برای توصیف آسیب یک سازه است. در این مقاله، هم‌بستگی بین پارامترهای طیفی یک زمین‌لرزه و شاخص‌های پارک- انگ بررسی می‌شود. برای این منظور، سه قاب بتن مسلح با ارتفاع‌های مختلف، تحت رکوردهای زمین‌لرزه حوزۀ دور به‌روش دینامیکی غیرخطی تحلیل شده‌ و هم‌بستگی بین پارامترهای طیفی و شاخص‌های پارک- انگ قاب‌ها محاسبه شده است. نتایج نشان می‌دهد که در همه قاب‌ها، بیش‌تر پارامترهای طیفی هم‌بستگی قوی با شدت آسیب دارند. از این‌رو برای برآورد پتانسیل آسیب زمین‌لرزه، برخی پارامترهای طیفی که هم‌بستگی زیادی با شدت آسیب دارند،  شاخص‌های مناسبی هستند. شدت هاوزنر، شدت طیف شتاب و شدت طیف سرعت، هم‌بستگی زیادی با شدت آسیب از خود نشان می‌دهند. در این مقاله، یک پارامتر طیفی جدید که هم‌بستگی بسیار خوبی با شدت آسیب دارد، به‌دست آمده است. http://jeg.khu.ac.ir/article-1-2717-fa.pdf 2017-11-01 135 160 10.18869/acadpub.jeg.11.3.135 زمین‌لرزه پارامترهای طیفی شدت آسیب شاخص پارک- انگ ضریب هم‌بستگی Correlations between Spectral Parameters of Earthquakes and Damage Intensity in Different RC Frames In recent decades many researchers have studied on the damage assessment of structures after a seismic event. To assess the damage of structures under an earthquake, it is so important to study the correlations between earthquake parameters and damages of the structures. A lot of seismic parameters have been defined by researchers to characterize an earthquake. Spectral parameters of an earthquake convey a variety of information about ground motion, so they can properly characterize an earthquake. Also a lot of damage indices were proposed by researchers to quantify the damage of the structures or to rank their vulnerability relative to each other. Park-Ang index is one of the best indices to describe the damage of a structure. In this paper, the correlations between spectral parameters of earthquakes and Park-Ang indices are studied. Three RC frames with different height are analyzed under far-fault earthquake records by nonlinear dynamic analyses. The correlations between spectral parameters and Park-Ang indices of the frames are calculated. The results show that in all the frames most of spectral parameters have strong correlations with damage intensity. In order to estimate the damage potential of an earthquake, some spectral parameters which have high correlations with damage intensity can be proper indices. Housner intensity, acceleration spectrum intensity and velocity spectrum intensity are shown to have strong correlations with damage intensity. In this paper, a new spectral parameter which has high correlation with damage intensity is achieved.  http://jeg.khu.ac.ir/article-1-2717-en.pdf 2017-11-01 135 160 10.18869/acadpub.jeg.11.3.135 Spectral parameters Damage intensity Park-Ang index Correlation coefficient Ali Massumi 1 AUTHOR Maryam Rahmati Selkisari 2 AUTHOR
معرفی روابط تجربی بهمنظور تخمین مقاومت فشاری تکمحوری سنگ‌های آهک با استفاده از نتایج آزمایشگاهی، مطالعۀ موردی؛ شمال ساوه در بسیاری از پروژه‌های مهندسی، تعیین دقیق ویژگی‌های مقاومتی و رفتاری سنگ‌ها اهمیت زیادی دارد. مقاومت فشاری تک‌محوری از جمله ویژگی‌های مهم در توصیف رفتار مقاومتی سنگ‌ها است که به‌عنوان یک پارامتر مهم در طراحی سازه‌ها به‌ویژه سازه‌های زیرزمینی استفاده می‌شود. تعیین این پارامتر با استفاده از روش‌های مستقیم از جمله آزمایش مقاومت فشاری تک‌محوری پرهزینه و وقت‌گیر است و در برخی از موارد تهیه و آماده‌سازی نمونه استاندارد به‌دلیل وجود سطوح ضعیف در بسیاری از سنگ‌ها مشکل است. در چنین مواردی انجام برخی آزمون‌های ساده و غیرمخرب و استفاده از روابط تجربی می‌تواند منجر به افزایش سرعت ارزیابی و کاهش هزینه‌ها شود. وجود این روابط حتی به‌صورت منطقه‌ای و یا محلی (مثلاً در محدوده‌ یک سازند زمین‌شناسی و یا یک لیتولوژی واحد) می‌تواند کمک مؤثری در تخمین این پارامتر به‌منظور استفاده در پروژه‌های ژئوتکنیکی باشد. در این تحقیق از سنگ‌های آهک موجود در محدودۀ شمال ساوه نمونه‌هایی تهیه شده و آزمایش‌های مقاومت تراکم تک‌محوری، بارنقطه‌ای، چکش اشمیت و سرعت موج برشی روی آن‌ها انجام شده است. سپس با ارزیابی‌های آماری انجام شده روی نتایج به‌دست آمده، روابط تجربی بین مقاومت فشاری تک‌محوری و نتایج سه آزمایش دیگر به‌دست آمده است. مقایسه بین مقادیر مقاومت فشاری تک‌محوری پیش‌بینی شده و مقادیر مشاهده شده نشان‌دهندۀ اعتبار روابط تجربی به‌دست آمده است. این روابط برای تخمین مقاومت فشاری سنگ‌های آهک در محدودۀ بررسی شده و سنگ‌های با شرایط مشابه زمین‌شناسی نتایج قابل قبولی را به‌دست دهد. http://jeg.khu.ac.ir/article-1-2525-fa.pdf 2017-11-01 161 182 10.18869/acadpub.jeg.11.3.161 مقاومت فشاری تک‌محوری بارنقطه‌ای چکش اشمیت سرعت موج برشی سنگ آهک The new empirical formula to estimate the uniaxial compressive strength of limestone; south west of Tehran-Iran, as a case study In many rock engineering projects, accurate identification of rock strength properties is very important. Uniaxial compressive strength is one of the most important features to describe the resistive behavior of rocks which is used as an important parameter in the design of structures especially underground openings. Determination of this parameter using direct methods, including uniaxial compressive strength tests is costly and time-consuming, and also sometimes preparation of standard samples in many rocks is difficult. In such cases, the implementation of some simple and non-destructive tests and using empirical relations can increase the evaluation speed and reduce costs. These relations even regional or local (For example within a geological formation or a single lithology) can help in the estimation of these parameters in order to be used in geotechnical projects. In this study, samples of existing limestones in south west of Tehran (Capital of Iran) were prepared and uniaxial compressive strength, point load, Schmidt hammer and Shear wave velocity tests on which have been performed. Then by the statistical evaluations of the results, the empirical relations between uniaxial compressive strength and the results of other tests are obtained. The comparison between the predicted and observed values of uniaxial compressive strength represents the validity of obtained empirical relations. The application of the proposed relations for limestones in the study area and those with similar geological conditions will provide acceptable results. http://jeg.khu.ac.ir/article-1-2525-en.pdf 2017-11-01 161 182 10.18869/acadpub.jeg.11.3.161 Uniaxial compressive strength Point load Schmidt hammer Shear wave velocity limestone Correlation Ali M. Rajabi amrajabi@ymail.com; amrajabi@qom.ac.ir 1 University of Qom AUTHOR Alireza Hossini ah_hosseini71@yahoo.com 2 University of Qom AUTHOR Alireza Heidari parhan_joosh@yahoo.com 3 University of Qom AUTHOR
ORIGINAL_ARTICLE بررسی رفتار رادیه شمع تحت ترکیب بار قائم و افقی با استفاده از روش تاگوچی در این پژوهش نتایج بررسی پارامتریک به‌وسیلۀ روش اجزا محدود، مربوط به رفتار رادیه شمع، وابسته به متغیرهای قطر شمع، طول شمع، چیدمان شمع­ها و ضخامت رادیه، تحت بار جانبی و ترکیب بار ارائه شده است. روش تاگوچی با تحلیل واریانس (ANOVA) برای محاسبه نسبت مشارکت هر یک از این عوامل در جابه‌جایی جانبی رادیه شمع به‌کار گرفته شده است. نتایج به‌دست آمده نشان می‌دهد قطر شمع مؤثرترین فاکتور در تغییرشکل جانبی رادیه شمع تحت بار افقی تنها است. لیکن در حالت ترکیب بار، طول شمع بزرگ‌ترین درصد مشارکت را در کاهش تغییرشکل افقی دارد.   http://jeg.khu.ac.ir/article-1-2514-fa.pdf 2017-11-01 183 204 10.18869/acadpub.jeg.11.3.183 رادیه شمع طراحی بهینه بار قائم بار جانبی روش تاگوچی Evaluation of Piled Raft Behavior based on the Taguchi Method subjected to Combination of Vertical and Horizontal Loads The results of an ongoing FEM parametric study are presented regarding the dependence of the resulting piled raft behavior under lateral load and combination of loads on pile diameter, pile length, arrangement of piles and raft thickness. Taguchi method with Analysis of Variance (ANOVA) was employed to calculate the contribution ratio of these factors on the lateral displacement of piled raft. The obtained results of this study show that the pile diameter is an effective factor in horizontal deformation of the piled raft under pure horizontal load. However, in the case of load combinations, the pile length has the highest participation ratio in reducing the horizontal deformations.     http://jeg.khu.ac.ir/article-1-2514-en.pdf 2017-11-01 183 204 10.18869/acadpub.jeg.11.3.183 piled raft optimum design vertical load lateral load Taguchi method. Yasaman Salahshour yasaman.salahshour@gmail.com 1 Imam Khomeini International University AUTHOR Alireza Ardakani a.ardakani@eng.ikiu.ac.ir 2 Imam Khomeini International University AUTHOR